Skip to main content

PMS 437

Fuels: Canopy Fuel Characteristics

  1. Canopy Cover-Percentage or Class
  2. Stand (Canopy)-Height-ft or m
  3. Canopy Base Height-ft or m
  4. Canopy Bulk Density-kg/m3 or lb/ft3

Canopy Cover - Percentage or Class

The forest Canopy Cover (CC) describes the percent cover or cover class of the tree canopy in a stand. Specifically, CC describes the vertical projection of the tree canopy onto an imaginary horizontal surface representing the ground’s surface. Estimate of CC is used in adjustment of 20 feet winds to mid-flame, fuel moisture conditioning and spotting distance models.

The scale illustrates representative CC percentages and ranges within each cover class.

Image
Canopy Cover classification. This graphic depicts from above views of canopy cover and its effect on wind sheltering/reduction.

For surface fuels sheltered by a forest canopy on flat terrain. (Scott 2007)

Canopy Cover Wind Sheltering
CC ≤ 5% Unsheltered
5% < CC ≤ 10% Partially Sheltered
10% < CC ≤ 15% Partially Sheltered
15% < CC ≤ 30% Fully Sheltered, Open
30% < CC ≤ 50% Fully Sheltered, Open
CC > 50% Fully Sheltered, Closed

Return to Top

Stand (Canopy) Height-ft or m

The Stand or Canopy Height (SH) describes the average height of the top of the vegetated canopy. SH estimates are used in adjustment of 20 feet winds to mid-flame and in spotting distance models.

Return to Top

Canopy Base Height-ft or m

The forest Canopy Base Height (CBH) describes the average height from the ground to a forest stand's canopy bottom. Specifically, it is the lowest height in a stand at which there is a sufficient amount of forest canopy fuel to propagate fire vertically into the canopy. Using this definition, ladder fuels such as lichen, dead branches, and small trees are incorporated. Estimate of CBH is used in the Crown Fire Initiation model.

Image
Describing a Forest Canopy. This graphic highlights the way to think about the primary descriptors for crown fire prediction. Crown Bulk Density describes the crown fuel load and distribution. Stand Height describes height of canopy tops. Crown Base height represents the difficulty for surfaces fires to ignite the canopy. And Foliar Moisture content suggest how readily the canopy will burn.

Return to Top

Canopy Bulk Density-kg/m3 or lb/ft3

The forest Canopy Bulk Density (CBD) describes the density of available canopy fuel in a stand. It is defined as the mass of available canopy fuel per canopy volume unit. Typical units are either kg/m3 (LANDFIRE default) or lb/ft3 (BehavePlus default). CBD estimates are used to determine the threshold spread rate, or surface wind speed, used to determine the likelihood of active crown fire.

Image
Canopy Bulk Density is a difficult concept to apply to crown fire predictions. This image shows that CBD varies with height above ground.

The following graph, also displayed in the Crown Fire section under Crown Fire Initiation and Propagation, displays the threshold surface 20 feet wind speed or Crowning Index, necessary for producing active crown fire given a specific canopy bulk density.

Image
Crowning Index. Based on Rothermel crown fire spread model, canopy bulk density can be related to the windspeed required to sustain crown fire.

Print PDF

NWCG Latest Announcements

The Incident Position Standards and Next Generation Position Task Book are now available for Status/Check-In Recorder (SCKN)

Date: August 27, 2024
Contact: Incident Planning Subcommittee 

NWCG is excited to announce that the NWCG Incident Position Standards for Status/Check-In Recorder, PMS 350-32, NWCG Position Task Book for Status/Check-In Recorder (SCKN), PMS 311-32, and Checking In Resources Customer Service Job Aid, J-111 are now available.

The Performance Support Package, which for SCKN includes the Incident Position Standards, Next Generation Position Task Book, and job aid were developed through the Incident Performance and Training Modernization (IPTM) effort. The Performance Support Package will support trainees, those qualified in the position, and evaluators.

References:

NWCG Status/Check-In Recorder Position Page

NWCG Incident Position Standards for Status/Check-In Recorder, PMS 350-32

NWCG Position Task Book for Status/Check-In Recorder (SCKN), PMS 311-32

Checking In Resources Customer Service Job Aid, J-111

The Next Generation Position Task Book and Incident Position Standards are now available for Safety Officer, Field (SOFF)

Date: July 26, 2024
Contact: Risk Management Committee 

NWCG is excited to announce that the NWCG Incident Position Standards for Safety Officer, Field, PMS 350-81 and NWCG Position Task Book for Safety Officer, Field (SOFF), PMS 311-81 are now available.

The Safety Officer, Field (SOFF) is responsible for monitoring operations on an incident from a risk management perspective to provide for the welfare of incident resources and the public. The new Incident Position Standards and Next Generation Position Task Book are developed through the Incident Performance and Training Modernization (IPTM) effort.

References:

NWCG Safety Officer, Field (SOFF) Position

NWCG Incident Position Standards for Safety Officer, Field, PMS 350-81

NWCG Position Task Book for Safety Officer, Field (SOFF), PMS 311-81

Updated NWCG Standards for Electronic Documentation (eDoc), PMS 277

Date: July 25, 2024
Contact: Incident Planning Subcommittee 

The Incident Planning Subcommittee has updated the NWCG Standards for Electronic Documentation (eDoc), PMS 277.

The NWCG Standards for Electronic Documentation (eDoc) establishes the standards for collection and retention of records on wildland fires. This July 2024 update will provide incident management teams the most current standards required to maintain incident records and submit them to host units at the close of an incident.

References:

NWCG Standards for Electronic Documentation (eDoc), PMS 277

eDoc Box Directory (zip file)

NWCG Off-Highway Vehicle Typing Standard Request for Comment

Date: July 24, 2024
Contact: Mobile Fire Equipment Subcommittee 

The Mobile Fire Equipment Subcommittee has released Equipment Bulletin 24-002 NWCG Off-Highway Vehicle (OHV) Typing Standard - Request for Comment. This bulletin outlines the proposed NWCG OHV typing standard, as well as the business need for establishing the standard. Comments on the proposed standard will be accepted through August 15th using the comment form linked below.

References:

ETC-EB-2024-02: NWCG Off-Highway Vehicle (OHV) Typing Standard - Request for Comment

NWCG Off-Highway Vehicle (OHV) Typing Standard Comment Form